Presentation at the conference
PARTICIPATION IN CONFERENCES
INTERNATIONAL SCIENTIFIC DISCUSSION: PROBLEMS, TASKS AND PROSPECTS, Brighton, United Kingdom 19-20.03.2023
Technical justification of the sectional construction of the pressure plate in the die-cutting press
It was stated that the die-cutting equipment belongs to the category of heavily loaded equipment because the drive overcomes significant technological resistances resulting from sweeps die-cutting. Presses of the equipment are equipped with both wedge-lever mechanisms and eccentric ones to ensure cyclic vertical movement of the pressure plate. It is emphasized that automatic platens create a force loading in the die-cutting of sweeps of more than two hundred tons. A sectional construction of a pressure plate with an eccentric drive was suggested. Such a pressure plate design is designed to ensure consistent interaction of the tools of the die-cutting stamp with the sections of the cardboard cutting to minimize the force loading of the drive. Values of the displacement invariant of all three sections of the pressure plate were obtained, the eccentrics of which are shifted in the angular direction. It was established that an increase in the cardboard thickness requires a similar change in the angular displacement of the eccentrics on the drive shafts in the adjacent sections. Further research on a test stand is planned.
DOI https://doi.org/10.51582/interconf.19-20.03.2023.055
SCIENTIFIC RESEARCH IN THE MODERN WORLD
The 5th International scientific and practical conference “Scientific research in the modern world” (March 9-11, 2023) Perfect Publishing, Toronto, Canada. 2023. 471 p.
REASONING FOR THE USE OF CRANK-GEAR DRIVE OF PRESSURE SEGMENT IN THE DIE-CUTTING PRESS
The causes of large technological loads in a flat die-cutting press were analyzed. The use of a segmental pressure device was suggested to minimize them. It reduces the contact area of “a pressure device and die-cutting stamp” in pairs. As a result, the die-cutting press’s technological loads, metal intensity, and energy content are reduced. Two crank-gear mechanisms installed in parallel were suggested for the drive of the carriage with a pressure cylindrical segment. Such a drive ensures cyclic rolling of the segment on the cardboard cutting, reducing technological loads.
Keywords: die-cutting, press, segment, effort, drive, crank, tooth gear
MODERN KNOWLEDGE: RESEARCH AND DISCOVERIES, VANCOUVER, CANADA May 19-20, 2023
Sectional design of the pressure plate in the die-cutting press with wedging mechanisms: justification of application
The reasons for high technological loads during die-cutting and the design schemes of punching presses are analyzed. Based on the analysis of scientific research, it was found that minimizing the contact area between the pressure plate and the cardboard is necessary to reduce technological efforts. An original pressure plate drive design scheme with sectional construction is proposed. The nature of the joint movement of the sections of the pressure plate is analyzed, and the advantages of the offered die-cutting press are outlined.
2017 – International Symposium of Mechanical Engineers, NU “LP”, Lviv, Ukraine
2016 – Progressive Directions of Development Technological Systems, LNTU, Lutsk, Ukraine
2016 – Skorin’s Readings 2016, BSTU, Minsk, Belarus
2015 – EduChanging-2015: Education, Technology, Innovation for the Future, Moskow, Russia
2015 – International Symposium of Mechanical Engineers, NU “LP”, Lviv, Ukraine
2014 – SoftServe IT Weekend S.M.I.L.E., SoftServe, Lviv, Ukraine
2013 – Graphics of the XXI Century, SevNTU, Sevastopol, Ukraine
2012 – Graphics 2012, SevNTU, Sevastopol, Ukraine
2012 – IT in Education, Science and Technology, ChDTU, Cherkasy, Ukraine
2012 – IT in Education, Economics and Social Sphere, KIPU, Simferopol, Ukraine
2011 – Applied Geometry and Engineering Graphics, LNTU, Lutsk, Ukraine
2011 – Graphics of the XXI Century, SevNTU, Sevastopol, Ukraine
Reward at the conference
COMPETITIONS
• 2015 – the winner of the international open competition “Shape the Future 2015” Autodesk CIS, Moskow, Russia
• 2013 – the winner of the open competition of scientific works “Youth and printing” at the Ukrainian Academy of Printing, Lviv, Ukraine
With Dr. Randy Swearer in Skolkovo
With Dr. Durnyak B.
